Drybase Plaster Mesh Membrane LP is produced using high-quality Polypropylene material and provides a barrier to moisture, salts and vapour. It is a slimline membrane with 2.5mm studs on the rear that enables the management of moisture without significantly reducing room space. A plastic mesh is welded to the front surface of the membrane, allowing it to accept plaster coats via standard trowel application or as a base for dot and dab plasterboard application.
Sovereign Fleeced Overseal Tape is a synthetic butyl/rubber based preformed strip sealant laminated with a non woven polyester fleece. It's primarily used for creating a joint overseal where SovDrain Cavity Drain Membranes are used.
Size
2mm x 100mm x 10m
Length
10m
Thickness
2mm ± 0.2mm
Width
100mm
Material
Synthetic Butyl/Rubber Sealant Laminated with Non-woven Polyester Fleece
A watertight low-profile sheet membrane for protection against dampness in walls without the need to drill and install plugs. The membrane is a 1.5 mm thick flexible polypropylene sheet with a fleeced surface on both sides. The two fleeces ensure good adhesion to the wall by means of Drybase Flex Adhesive, as well as the direct application of plaster to the face.
Size
1.2 × 15 m
Length
15 m
Thickness
1.5 mm
Width
1.2 m
Weight
9.6
Material
Fleece
Colour
Black
Coverage
1 × 15 m
Pack Quantity
1
Certifications Met
ISO 9001, ISO 14001, Fire Rating: Class F (EN 13501)
Sovereign CDM8 membrane provides a robust drainage membrane suitable for above and below ground applications to walls and floors as part of the SovDrain waterproofing system. With a fast track application, the membrane protects new finishes from the effects of dampness and/or salt contamination in above ground situations, and prevents water ingress below ground in areas such as cellars, basements, vaults, and tunnels. This membrane has a relatively low stud profile (8mm), thus minimising wall and floor level changes. The CDM8 membrane is typically finished with either a pre-treated timber stud partition wall and plasterboard or independent stud metal frame system. The floors can be finished with a Sovereign SBR modified screed (minimum 65mm) or a floating floor.
Drybase Plaster Mesh Membrane LP is produced using high-quality Polypropylene material and provides a barrier to moisture, salts and vapour. It is a slimline membrane with 2.5mm studs on the rear that enables the management of moisture without significantly reducing room space. A plastic mesh is welded to the front surface of the membrane, allowing it to accept plaster coats via standard trowel application or as a base for dot and dab plasterboard application.
Sovereign Fleeced Overseal Tape is a synthetic butyl/rubber based preformed strip sealant laminated with a non woven polyester fleece. It's primarily used for creating a joint overseal where SovDrain Cavity Drain Membranes are used.
A watertight low-profile sheet membrane for protection against dampness in walls without the need to drill and install plugs. The membrane is a 1.5 mm thick flexible polypropylene sheet with a fleeced surface on both sides. The two fleeces ensure good adhesion to the wall by means of Drybase Flex Adhesive, as well as the direct application of plaster to the face.
Sovereign CDM8 membrane provides a robust drainage membrane suitable for above and below ground applications to walls and floors as part of the SovDrain waterproofing system. With a fast track application, the membrane protects new finishes from the effects of dampness and/or salt contamination in above ground situations, and prevents water ingress below ground in areas such as cellars, basements, vaults, and tunnels. This membrane has a relatively low stud profile (8mm), thus minimising wall and floor level changes. The CDM8 membrane is typically finished with either a pre-treated timber stud partition wall and plasterboard or independent stud metal frame system. The floors can be finished with a Sovereign SBR modified screed (minimum 65mm) or a floating floor.