e, it is flexible and lightweight and will accommodate a multitude of wall finishes
Due to its ease of use and flexibility it can be cut around light switches/sockets/radiator brackets, and is minimally invasive in its installation
Very often , door architraves and skirting can remain in place, and because of its malleability
ISO-THERM is vapour permeable but waterproof
Because of its high thermal benefit and the prevention of any natural damp transference
highly resistant to any formation of surface mould
The sheer speed of application and the ability to apply directly to sound plastered walls, means that large areas can be applied in a very short space of time
Both residential and commercial properties suffering from cold and damp/ mouldy walls can be improved substantially with minimum of disruption
Drybase Plaster Mesh Membrane LP is produced using high-quality Polypropylene material and provides a barrier to moisture, salts and vapour. It is a slimline membrane with 2.5mm studs on the rear that enables the management of moisture without significantly reducing room space. A plastic mesh is welded to the front surface of the membrane, allowing it to accept plaster coats via standard trowel application or as a base for dot and dab plasterboard application.
Drybase Liquid-Applied DPM is a single-pack barrier coating for above ground use. It is supplied ready to use. It is available in black or white with a consistency similar to that of thick emulsion paint. The product is applied in two coats. Drybase Liquid-Applied DPM Is suitable for use on solid floors, embedded timbers and walls. Once applied, the product cures to form a membrane that is flexible and elastic. Drybase Liquid-Applied DPM is water- based and can be applied to damp substrates by brush, roller, or spray. The applied product is typically touch-dry in one hour.
Size
1 Litre
Interior or Exterior Use
Interior
Coverage per Litre
4.5 m2 per 5 litres for vapour barrier, 7 – 9 m2 per 5 litres for general DPM
Fleece backed 100 mm waterproof butyl tape gives a well-bonded seal to the mesh face of Drybase. Plaster Membrane. The fleece backing to this tape also accepts a plaster coat finish as well as plaster adhesive where a dot and dab plasterboard system is preferred.
This Knauf Insulation Loft Roll Combi Cut 44 measures 8.05m in length, 1.14 m in width, and has a thickness of 15cm, providing a total coverage area of 9.18m2. Perfect for insulating cold roof spaces at ceiling height. It functions to optimise thermal retention by minimising heat transfer. The material is non-combustible and attains the highest fire-resistance classification (Euroclass A1). It is manufactured using ECOSE Technology, an environmentally sustainable binder derived from plant-based resources.
Length
8050 mm
Weight
12.94 kg
Thickness
150 mm
Width
1140 mm
Material
Glass Mineral Wool
Usage
Thermal Loft insulation for a pitched roof at ceiling level only. Standard loft insulation which runs between timber joists and then cross layered on top.
Coverage
9.18 m2
Thermal Conductivity
0.044 W/mK
Pack Quantity
1
Certifications Met
Euroclass A1 Reaction to Fire Classification, Eurofins Gold
Drybase Plaster Mesh Membrane LP is produced using high-quality Polypropylene material and provides a barrier to moisture, salts and vapour. It is a slimline membrane with 2.5mm studs on the rear that enables the management of moisture without significantly reducing room space. A plastic mesh is welded to the front surface of the membrane, allowing it to accept plaster coats via standard trowel application or as a base for dot and dab plasterboard application.
Drybase Liquid-Applied DPM is a single-pack barrier coating for above ground use. It is supplied ready to use. It is available in black or white with a consistency similar to that of thick emulsion paint. The product is applied in two coats. Drybase Liquid-Applied DPM Is suitable for use on solid floors, embedded timbers and walls. Once applied, the product cures to form a membrane that is flexible and elastic. Drybase Liquid-Applied DPM is water- based and can be applied to damp substrates by brush, roller, or spray. The applied product is typically touch-dry in one hour.
Fleece backed 100 mm waterproof butyl tape gives a well-bonded seal to the mesh face of Drybase. Plaster Membrane. The fleece backing to this tape also accepts a plaster coat finish as well as plaster adhesive where a dot and dab plasterboard system is preferred.
This Knauf Insulation Loft Roll Combi Cut 44 measures 8.05m in length, 1.14 m in width, and has a thickness of 15cm, providing a total coverage area of 9.18m2. Perfect for insulating cold roof spaces at ceiling height. It functions to optimise thermal retention by minimising heat transfer. The material is non-combustible and attains the highest fire-resistance classification (Euroclass A1). It is manufactured using ECOSE Technology, an environmentally sustainable binder derived from plant-based resources.