Kit contains: x1 Dryrod 50 Box x1 Dryzone System Hole Clearing Tool - x1 Dryzone System Rod Cutting Tool- x1 Dryzone Drill Bit - 12mm x 300mm - x1 Stormdry Xr Mortar - No fuss, no mess, no stress. Dryrod is the next generation of rising damp treatment developed by Safeguard Europe Ltd. The patented, BBA approved 12mm diameter DIY damp proofing rods carry a powerful water repellent material, which cures to form a powerful barrier to rising damp. Once they are inserted, the rods will start to dry out the wall by slowly diffusing water repellent deep into the damp masonry, curing to form a powerful barrier to further rising damp. Installation: Simply insert the 9" rods into a series of 12mm holes drilled into the lowest available continuous mortar course of the wall. No specialist pumps or mastic guns required. A normal hammer drill will suffice. Once installed they diffuse the active ingredient deep into the wall before it cures to form a water-repellent chemical damp course. Advantages over other methods: The most effective rising damp treatment available - Proven to work even up to 95% saturation Quick & easy to install DIY rising damp treatment - Simply drill holes & insert the damp-proofing rods to form a new chemical damp course. No mess to clean up - The active ingredient is contained within the rods so there's no chance of messy spillages that occur with other solutions for damp proofing for walls.
Dryzone is a special damp proofing cream that is introduced along the mortar course at regular intervals by injecting it into pre-drilled holes. The Dryzone then diffuses before curing to form a continuous water repellent barrier. This prevents the damp from rising up the wall.
A radical chemical blend containing a sophisticated mixture of alkaline materials and wetting agents to attack varied types of blockages whether caused by hair, grease, fat, oils, etc.. Heavier than water the unique formula holds the active chemicals together, allowing them to sink to the source of the problem with minimum loss of activity.
The RLT CLEARMOULD SPRAY is a non-aerosol, water-based spray which is a quick and effective material for treating mould and mildew contaminations on carpets, leather goods, clothes, furniture and soft furnishings.
Spray affected surfaces, allow to dry and vacuum with a HEPA filter cleaner. For leather goods after cleaning apply a good quality polish.
RLT CLEARMOULD SPRAY can also be used to treat musty smells arising from heavy airborne contamination of mould spores in rooms, inside wardrobes and cupboards. Spray on the affected areas and leave for 30 minutes to allow product to work and dry.
The products are approved by the Health and Safety Executive under the Control of Pesticides Regulations (COPR) 1986 (as amended) for both amateur and professional use.
Size
235 ml
Suitable for
Soft Furnishings, Carpets, Curtains and Leather Goods
Coverage
0.5L per 4 to 5 Square meters
Interior or Exterior Use
Interior
Container Type
Plastic Bottle
Application Method
Spray
Type
Ready to use
Pack Quantity
Single
Certifications Met
Approved under COPR 1986(as amended) by the H&S Executive HSE No 4824
Kit contains: x1 Dryrod 50 Box x1 Dryzone System Hole Clearing Tool - x1 Dryzone System Rod Cutting Tool- x1 Dryzone Drill Bit - 12mm x 300mm - x1 Stormdry Xr Mortar - No fuss, no mess, no stress. Dryrod is the next generation of rising damp treatment developed by Safeguard Europe Ltd. The patented, BBA approved 12mm diameter DIY damp proofing rods carry a powerful water repellent material, which cures to form a powerful barrier to rising damp. Once they are inserted, the rods will start to dry out the wall by slowly diffusing water repellent deep into the damp masonry, curing to form a powerful barrier to further rising damp. Installation: Simply insert the 9" rods into a series of 12mm holes drilled into the lowest available continuous mortar course of the wall. No specialist pumps or mastic guns required. A normal hammer drill will suffice. Once installed they diffuse the active ingredient deep into the wall before it cures to form a water-repellent chemical damp course. Advantages over other methods: The most effective rising damp treatment available - Proven to work even up to 95% saturation Quick & easy to install DIY rising damp treatment - Simply drill holes & insert the damp-proofing rods to form a new chemical damp course. No mess to clean up - The active ingredient is contained within the rods so there's no chance of messy spillages that occur with other solutions for damp proofing for walls.
Dryzone is a special damp proofing cream that is introduced along the mortar course at regular intervals by injecting it into pre-drilled holes. The Dryzone then diffuses before curing to form a continuous water repellent barrier. This prevents the damp from rising up the wall.
A radical chemical blend containing a sophisticated mixture of alkaline materials and wetting agents to attack varied types of blockages whether caused by hair, grease, fat, oils, etc.. Heavier than water the unique formula holds the active chemicals together, allowing them to sink to the source of the problem with minimum loss of activity.
The RLT CLEARMOULD SPRAY is a non-aerosol, water-based spray which is a quick and effective material for treating mould and mildew contaminations on carpets, leather goods, clothes, furniture and soft furnishings.
Spray affected surfaces, allow to dry and vacuum with a HEPA filter cleaner. For leather goods after cleaning apply a good quality polish.
RLT CLEARMOULD SPRAY can also be used to treat musty smells arising from heavy airborne contamination of mould spores in rooms, inside wardrobes and cupboards. Spray on the affected areas and leave for 30 minutes to allow product to work and dry.
The products are approved by the Health and Safety Executive under the Control of Pesticides Regulations (COPR) 1986 (as amended) for both amateur and professional use.