Bostik Wide Jointing Compound for paths & patios is a blend of polymers and sand that bind together on contact with air, providing an easy to use alternative to conventional cement mortar.
Once cured it forms a solid joint, which will resist weed growth and sand loss from power washing or mechanical cleaning. Bostik Wide Jointing Compound is a single component and does not require mixing or special tools.
It's suitable for most types of domestic paving including natural stone, concrete, clay and terracotta in joints 5mm to 30mm in width. It is water permeable allowing the paving to drain and, when cured, is unaffected by salt and freezing conditions.
Kit contains: x1 Dryrod 50 Box x1 Dryzone System Hole Clearing Tool - x1 Dryzone System Rod Cutting Tool- x1 Dryzone Drill Bit - 12mm x 300mm - x1 Stormdry Xr Mortar - No fuss, no mess, no stress. Dryrod is the next generation of rising damp treatment developed by Safeguard Europe Ltd. The patented, BBA approved 12mm diameter DIY damp proofing rods carry a powerful water repellent material, which cures to form a powerful barrier to rising damp. Once they are inserted, the rods will start to dry out the wall by slowly diffusing water repellent deep into the damp masonry, curing to form a powerful barrier to further rising damp. Installation: Simply insert the 9" rods into a series of 12mm holes drilled into the lowest available continuous mortar course of the wall. No specialist pumps or mastic guns required. A normal hammer drill will suffice. Once installed they diffuse the active ingredient deep into the wall before it cures to form a water-repellent chemical damp course. Advantages over other methods: The most effective rising damp treatment available - Proven to work even up to 95% saturation Quick & easy to install DIY rising damp treatment - Simply drill holes & insert the damp-proofing rods to form a new chemical damp course. No mess to clean up - The active ingredient is contained within the rods so there's no chance of messy spillages that occur with other solutions for damp proofing for walls.
Dryzone is a special damp proofing cream that is introduced along the mortar course at regular intervals by injecting it into pre-drilled holes. The Dryzone then diffuses before curing to form a continuous water repellent barrier. This prevents the damp from rising up the wall.
Stormdry MAX Enhanced Waterproofing Barrier is a clear gel coating providing lasting waterproofing, crack-bridging and anti-graffiti protection. It can be used on masonry, stone, concrete, selected metals and painted surfaces. It can be used as a top coat for Stormdry Masonry Protection Cream when multiple fine cracking is seen on the wall surface. Stormdry Max bridges cracks up to 0.6 mm wide providing protection against penetrating damp, giving up to 10 years weather protection. In anti-graffiti application, it will take up to 15 wash cycles to eliminate any graffiti applied to the surface coating and offers low-level flood resistance. The clear liquid is air moisture curing and is ready for use. It can be applied by brush and roller. The coating is partially breathable and gives a semi-gloss appearance which fades with time.
A cementitious, ready-mixed, rapid setting compound to stop water and moisture ingress. Drybase Waterproofing Plug can be used internally or externally as a waterproof plugging mortar or where rapid setting and early strength gain is required: Plugging water leaks and seepage. Sealing leaking cracks. Sealing wet surfaces. Plugging leaks in earthenware pipes. Caulking tunnel segment joints. Fixings in water structures where immediate use is required.
Kit contains: x1 Dryrod 50 Box x1 Dryzone System Hole Clearing Tool - x1 Dryzone System Rod Cutting Tool- x1 Dryzone Drill Bit - 12mm x 300mm - x1 Stormdry Xr Mortar - No fuss, no mess, no stress. Dryrod is the next generation of rising damp treatment developed by Safeguard Europe Ltd. The patented, BBA approved 12mm diameter DIY damp proofing rods carry a powerful water repellent material, which cures to form a powerful barrier to rising damp. Once they are inserted, the rods will start to dry out the wall by slowly diffusing water repellent deep into the damp masonry, curing to form a powerful barrier to further rising damp. Installation: Simply insert the 9" rods into a series of 12mm holes drilled into the lowest available continuous mortar course of the wall. No specialist pumps or mastic guns required. A normal hammer drill will suffice. Once installed they diffuse the active ingredient deep into the wall before it cures to form a water-repellent chemical damp course. Advantages over other methods: The most effective rising damp treatment available - Proven to work even up to 95% saturation Quick & easy to install DIY rising damp treatment - Simply drill holes & insert the damp-proofing rods to form a new chemical damp course. No mess to clean up - The active ingredient is contained within the rods so there's no chance of messy spillages that occur with other solutions for damp proofing for walls.
Dryzone is a special damp proofing cream that is introduced along the mortar course at regular intervals by injecting it into pre-drilled holes. The Dryzone then diffuses before curing to form a continuous water repellent barrier. This prevents the damp from rising up the wall.
Stormdry MAX Enhanced Waterproofing Barrier is a clear gel coating providing lasting waterproofing, crack-bridging and anti-graffiti protection. It can be used on masonry, stone, concrete, selected metals and painted surfaces. It can be used as a top coat for Stormdry Masonry Protection Cream when multiple fine cracking is seen on the wall surface. Stormdry Max bridges cracks up to 0.6 mm wide providing protection against penetrating damp, giving up to 10 years weather protection. In anti-graffiti application, it will take up to 15 wash cycles to eliminate any graffiti applied to the surface coating and offers low-level flood resistance. The clear liquid is air moisture curing and is ready for use. It can be applied by brush and roller. The coating is partially breathable and gives a semi-gloss appearance which fades with time.
A cementitious, ready-mixed, rapid setting compound to stop water and moisture ingress. Drybase Waterproofing Plug can be used internally or externally as a waterproof plugging mortar or where rapid setting and early strength gain is required: Plugging water leaks and seepage. Sealing leaking cracks. Sealing wet surfaces. Plugging leaks in earthenware pipes. Caulking tunnel segment joints. Fixings in water structures where immediate use is required.