Visqueen Building Products ECO TPS range is a blown film of extruded low-density polyethylene. Visqueen ECO TPS range is a high quality Temporary Protective Sheeting (TPS) manufactured from 100% Recycled LDPE.
Drybase Liquid-Applied DPM is a single-pack barrier coating for above ground use. It is supplied ready to use. It is available in black or white with a consistency similar to that of thick emulsion paint. The product is applied in two coats. Drybase Liquid-Applied DPM Is suitable for use on solid floors, embedded timbers and walls. Once applied, the product cures to form a membrane that is flexible and elastic. Drybase Liquid-Applied DPM is water- based and can be applied to damp substrates by brush, roller, or spray. The applied product is typically touch-dry in one hour.
Size
1 Litre
Interior or Exterior Use
Interior
Coverage per Litre
4.5 m2 per 5 litres for vapour barrier, 7 – 9 m2 per 5 litres for general DPM
Fleece backed 100 mm waterproof butyl tape gives a well-bonded seal to the mesh face of Drybase. Plaster Membrane. The fleece backing to this tape also accepts a plaster coat finish as well as plaster adhesive where a dot and dab plasterboard system is preferred.
Dryrod is the next generation of rising damp treatment developed by Safeguard Europe Ltd. The patented, BBA approved 12mm diameter DIY damp proofing rods carry a powerful water repellent material, which cures to form a powerful barrier to rising damp. Once they are inserted, the rods will start to dry out the wall by slowly diffusing water repellent deep into the damp masonry, curing to form a powerful barrier to further rising damp. Installation: Simply insert the 9" rods into a series of 12mm holes drilled into the lowest available continuous mortar course of the wall. No specialist pumps or mastic guns required. A normal hammer drill will suffice. Once installed they diffuse the active ingredient deep into the wall before it cures to form a water-repellent chemical damp course. Advantages over other methods: The most effective rising damp treatment available - Proven to work even up to 95% saturation Quick & easy to install DIY rising damp treatment - Simply drill holes & insert the damp-proofing rods to form a new chemical damp course. No mess to clean up - The active ingredient is contained within the rods so there's no chance of messy spillages that occur with other solutions for damp proofing for walls.
Visqueen Building Products ECO TPS range is a blown film of extruded low-density polyethylene. Visqueen ECO TPS range is a high quality Temporary Protective Sheeting (TPS) manufactured from 100% Recycled LDPE.
Drybase Liquid-Applied DPM is a single-pack barrier coating for above ground use. It is supplied ready to use. It is available in black or white with a consistency similar to that of thick emulsion paint. The product is applied in two coats. Drybase Liquid-Applied DPM Is suitable for use on solid floors, embedded timbers and walls. Once applied, the product cures to form a membrane that is flexible and elastic. Drybase Liquid-Applied DPM is water- based and can be applied to damp substrates by brush, roller, or spray. The applied product is typically touch-dry in one hour.
Fleece backed 100 mm waterproof butyl tape gives a well-bonded seal to the mesh face of Drybase. Plaster Membrane. The fleece backing to this tape also accepts a plaster coat finish as well as plaster adhesive where a dot and dab plasterboard system is preferred.
Dryrod is the next generation of rising damp treatment developed by Safeguard Europe Ltd. The patented, BBA approved 12mm diameter DIY damp proofing rods carry a powerful water repellent material, which cures to form a powerful barrier to rising damp. Once they are inserted, the rods will start to dry out the wall by slowly diffusing water repellent deep into the damp masonry, curing to form a powerful barrier to further rising damp. Installation: Simply insert the 9" rods into a series of 12mm holes drilled into the lowest available continuous mortar course of the wall. No specialist pumps or mastic guns required. A normal hammer drill will suffice. Once installed they diffuse the active ingredient deep into the wall before it cures to form a water-repellent chemical damp course. Advantages over other methods: The most effective rising damp treatment available - Proven to work even up to 95% saturation Quick & easy to install DIY rising damp treatment - Simply drill holes & insert the damp-proofing rods to form a new chemical damp course. No mess to clean up - The active ingredient is contained within the rods so there's no chance of messy spillages that occur with other solutions for damp proofing for walls.